Each DataMaxx EGT Module allows you to add up to four additional temperature sensors for exhaust gas temperature, cylinder head temperature, oil temperature, water temperature, etc. to your DataMaxx Main Module. CAN Bus wiring only requires a single four conductor cable to connect the EGT Module to the Main Module, simplyfing installation.
This K&R Delay Box Dash Kit allows you to mount your Pro-Cube in a dragster using this bolt-in kit.
The DataMaxx Remote SD Module is designed specifically for vehicles that are using magneto’s. Magneto’s disperse a wide range of electromagnetic noise and it is necessary to get the SD circuit physically far away from that radius of noise corruption. The remote SD comes with a 15 foot cable and can also be used as a convenient way to mount the SD card in an easy to reach location.
This Pro Dash 16v Adapter allows you to run your new Computech Pro Dash with a 16v battery. This 16v knockdown will make hooking up your Pro Dash a breeze and is required if using a 16v battery. Please know that the screen can function at 16-17v but will cut off beyond 17v which an alternator or battery can cause.
The Computech DataMaxx Data Logger samples at an extremelty fast rate, specifically 100 times per channel. That means for a typical Bracket kit we are sampling 650 times every second and for a professional kit it’s 1500 samples ever second.
Because of this we need an SD card that can sample at an extrodinary rate, specifically 150 times faster than the typical SD card.
We recommend purchasing your additional SD cards from Computech as we test each and every SD card to ensure proper speed before shipping them to you.
The Driveshaft Kit allows you to get an accurate reading of your driveshaft RPM. Available in small pinion (1.878″) and large pinion (2.190″). Includes drive shaft pick-up sensor, 15′ extension cable, trigger collar, and mounting bracket.
This Diesel RPM Sensor Kit comes with everything needed to monitor your diesel tractors engine rpm. Without a typical ignition system, we need to utilize the Dakota Sensor to monitor the flywheel or bolts on a pulley and the Dakota Digital Signal Conditioner Box to convert the signal into a usable Engine RPM Signal.
Kit includes: powered hall-effect pick-up sensor, 1 magnet and 15′ extension cable. Trigger collar and mounting bracket must be supplied by customer.
The Universal Shaft RPM Kit allows you to use your own collar yet still use a quality rpm sensor. Kit includes: pick-up sensor, 2 magnets and 15′ extension cable. Trigger collar and mounting bracket must be supplied by customer.
There is no better way to monitor and keep an eye on the health of your turbo like a Turbo RPM Kit. The sensor screws into the turbo housing and will monitor how fast the blades are actually spinning. This will give you an incredible amount of knowledge on how your turbo is performing and how your tune up changes affect the true turbo performance.
This Magneto Tach Adapter allows you to get a clean and smooth signal when utilizing a magneto ignition system.
The Vacuum Pressure Monitor Kit allows you to measure pressures from -14.7 to +30 inches of mercury. With calibration values available for inches of mercury (inHg) or pounds per square inch (psi) this vacuum pressure sensor works great for low range pressures that have a tendency to go into a vacuum state such as boost pressure.
Kit includes a stainless steel pressure transducer and 15′ extension cable. Compatible with most gases and fluids, including gasoline, methanol, oil, etc.
The 15 psi Pressure Monitor Kit is an extremely accurate low range pressure sensor, perfect for monitoring carbureted fuel pressure and boost psi.
Pressure sensor will monitor from 0 to 15 psi. Kit includes a stainless steel pressure transducer and 15′ extension cable. Compatible with most gases and fluids, including gasoline, methanol, oil, etc.
Pressure sensor will monitor from 0 to 100 psi. Kit includes a stainless steel pressure transducer and 15′ extension cable. Compatible with most gases and fluids, including gasoline, methanol, oil, etc.
This economy oil pressure sensor has a slightly slower sample rate than the other pressure sensors but works just fine for monitoring oil pressure. Sensor range is from 0 to 100 psi and does not come with any extension cable. Using a simple 18 gauge wire works just fine.
The 500 psi Pressure Monitor Kit is a great wide range pressure sensor that is still extremely accurate in low and high pressure environments. The 500 psi Pressure Monitor Kit is typically used for oil pressure, injected fuel psi, and transmission pressure. Pressure sensor will monitor from 0 to 500 psi. 500 psi Pressure Monitor Kit includes a stainless steel pressure transducer and 15′ extension cable. The 500 psi Pressure Monitor Kit is compatible with most gases and fluids, including gasoline, methanol, oil, etc.